Aug 02, 2024 Leave a message

Stone machinery and equipment used in the secondary processing of stone

The secondary processing of stone generally refers to the secondary processing of the slab (standard slab) after the bridge-cutting machine. (Often refers to special-shaped processing or manual processing).

 

5-axis-cnc-machine

Main equipment and tools for secondary processing of stone

Line machines, edge grinding machines, stone profiling machines, water jet machines, CNC stone cutting machines, back bolt hole machines, stone thickness machines, special-shaped edge grinding machines, granite drilling machines, digging machines, hand-held grinders, angle grinders, water grinders, hand cutting machines, CNC engraving machines, welding guns (flame guns) and other equipment and tools used for secondary processing of stone.

 

cnc-marble-cutting-machine

 

Some common methods of secondary processing of stone:

Thickness setting, edge grinding (small-mouth grinding), corner cutting, undercutting, slotting, bonding, chamfering, chamfering, R-face, drilling, sandblasting, burning, digging, small-section processing\splicing, mosaic, corner turning, etc.

A. Thickness setting: refers to setting the thickness of the back of one or several edges of the plate to a specified thickness. Some also require a full-thickness setting.

B. Small-section processing (small-section undercutting): refers to setting the thickness of the front of the plate to a certain size or cutting off a part of the small mouth of the plate according to the processing size. (Small-section processing generally requires polishing or processing to the same surface as the large surface)

C. Edge grinding (small-mouth grinding): polishing the small mouth of the plate, etc. Generally, straight edges are ground with a large grinder (because there is no water ripple), and those that cannot be ground with a water grinder are ground with a water grinder (such as chess piece edges, French edges, etc.). Marble abrasives: 60#-400#-800#-1200#-polishing

Granite abrasives: 50#-200#-400#-500#-800#-1500#-polishing

D. Angle cutting (changing): cutting at a specified angle, including tangent (face cutting), back cutting (bottom cutting), and octagonal cutting.

E. Cutting: Cut off part of the board according to the drawing or template according to the processing order requirements to make it into the required shape. (such as general plane cutting and R cutting)

F. Grooving: drawing grooves at specified positions according to a certain depth. There are front grooves (such as anti-slip grooves of stair slabs) and back grooves (such as drip grooves), as well as small grooves (such as dry hanging grooves).

G. Bonding: bonding two or more boards together with glue. There are angle-cutting bonding and fixed thickness bonding, as well as plane bonding. (Generally, the back of the bonding needs to be reinforced with stone, and some also need to drill holes and nails to make it more secure) 1/2 round edge (mostly countertops), fixed thickness bonding (mostly used in engineering boards)

H. Drilling: Drill holes with a drill bit at the corresponding position according to the size of the given hole. There are water pipe holes (such as water pipe installation holes in countertops), PC holes (a kind of dry hanging holes commonly used in Japan), back bolt holes (a kind of dry hanging holes), side holes (dry hanging holes), screw holes (such as screw holes on the back of countertops for fixing basins), etc.

I. Digging: Use a hole digger or angle grinder, hand cutter, etc. to process according to drawings or templates (generally large or irregular holes or holes that cannot be drilled directly by a drill bit) such as basin holes in countertops; square or rectangular switch boxes, etc.

J. Chamfering (face-taking): It is to chamfer the bevel edge, generally 45 degrees chamfering without special requirements

K. R surface: arc plate (inner arc and outer arc), round edge. The arc plate or round edge is processed according to the given R (usually the radius).

L. Chamfering: commonly known as chamfering, it is a chamfer within 1MM, so that the plate will not prick your hand.

M. Sandblasting: Steel sand (high cost, relatively deep) and sea sand (up to 1MM deep) are sprayed out through a spray gun through high-pressure gas, and hit on the sprayed object to make its surface rough (such as some fonts are sandblasted, such as spray flowers, anti-slip strips, etc.).

N. Burning: Oxygen and combustible gas are burned by the flame of a welding gun (burning gun) to burn the object, and the surface of the burned plate is rough.

Send Inquiry

Follow Us

whatsapp

Phone

E-mail

Inquiry