Jul 24, 2024 Leave a message

Introduction to the use of stone machines in granite surface technology

In addition to providing a unique natural artistic visual effect through natural texture, stone can also create a variety of visual experiences through various surface processing methods. Such rich changes are also one of the charms of stone.

 

1. The machine-cut surface is cut directly by a circular machine, sand saw machine, bridge saw cutting machine, and other equipment. The surface is rough and has obvious machine-cut lines.

machine-cut

 

2. Matt surface refers to a flat surface that has been polished less by a manual polisher or automatic stone polishing line using resin abrasives. Its glossiness is lower than that of the polished surface, generally around 30-50 or 60. It has a certain glossiness, but the reflection of light is weak. A plate with a flat and smooth surface and very low glossiness.

honed

3. A polished surface refers to a plate with a mirror-like gloss that is smooth and polished with a manual stone polisher or an automatic stone polishing line using resin abrasives.
The general brightness of stone can reach 80 or 90 degrees. Its characteristics are high brightness and strong reflection of light, which can fully display the rich and bright colors and natural texture of the stone itself.

polished

4. The flamed surface refers to the rough surface made by processing the stone surface with a high-temperature flame generated by a flame machine using acetylene, oxygen or propane, oxygen, or liquefied petroleum gas, oxygen as fuel.
The thickness of the stone has certain requirements to prevent the stone from breaking during processing, and the thickness is generally required to be at least 2CM. The surface of the flamed surface is rough and natural, non-reflective, fast to process, and relatively cheap.

flamed

5. The bush-hammered surface is made by hitting the surface of the stone with a hammer-shaped lychee skin, thus forming a rough surface shaped like lychee skin on the surface of the stone. It is divided into machine lychee surface machine and hand lychee surface handmade.

bush-hammered

6. The chiseled surface refers to the rough surface shaped like the appearance of longan skin formed by staggered hammering on the surface of the stone with a manual straight-shaped hammer or an automatic chopped axe surface processing machine.

chiseled

7. Flamed+brush

To eliminate the thorny characteristics of the burned surface, the stone is first burned with a flame machine and then brushed 3-6 times with a hand-held polisher or an automatic polisher using a steel brush to form an antique surface.

There are many ways to make an antique surface, such as water flushing after burning, acid etching, direct steel brushing or high-pressure water flushing. The processing of antique surfaces is time-consuming and expensive.

flamedbrush

8. Rough-picked

Fough-picked are made by hammering the stone surface with a chisel and a hammer into a pineapple-like slab.

fough-picked are rougher than lychee surface and longan surfaces. They can also be divided into coarse pineapple surface and fine pineapple surface.

rough-picked

9. Mushroom surface refers to the use of chisels and hammers to knock on the surface of the stone or the use of automatic mushroom surface processing machinery to form a plate shaped like an undulating mountain.

This processing method has certain requirements for the thickness of the stone. Generally, the bottom thickness is at least 3CM, and the raised part can be 2CM or more according to actual requirements.

mushroom

10. Natural surface
Natural surface refers to the processing method of splitting a piece of stone from the middle with a hammer or hydraulic stone splitter to form an uneven surface like the natural one.

naturalcleft

 

11. The grooved surface is made by using an intelligent bridge cutting machine to open grooves of a certain depth and width on the surface of the stone.

grooved

 

12. The sandblasting surface uses ordinary river sand or diamond sand instead of high-pressure water to wash the surface of the stone, forming a decorative surface with a smooth frosted effect.

sandblasted

 

13. Water jet uses high-pressure water to directly impact the surface of the stone, peeling off the softer components and forming a unique rough surface decorative effect.

water-jet

14. Pickling
The surface of the stone is corroded with strong acid, leaving small corrosion marks, which makes the appearance more rustic than polished surface.

 

pickling

Send Inquiry

Follow Us

whatsapp

Phone

E-mail

Inquiry